自恢复保险丝_综合综合综合综合综合网_贴片保险丝_综合自拍_插件保险丝_综合中文字幕_力特保险丝_力特经销商_SMD贴片保险丝_一次性保险丝厂家—深圳市集电通实业有限公司

Fuses vs PTCs(I)

2014-08-04 11:56:17 lipscall

This section provides guidance in choosing the best overcurrent circuit protection device...PTC or fuse...for the application. 

Many times choosing between using a Fuse or PTC is a matter of preference, though there are important considerations and common areas of applications where the use of one may be better than the other. 

For example, much of the design work for PCs, peripherals, and portable devices (smart phones, tablets, etc.) urges the use of PTCs because they are self-resettable; using a fuse that must be replaced each time an overcurrent condition occurs is unacceptable. 

In other cases, fuses may be more acceptable because they completely stop current in fault condition; this may be more desired if safety or avoidance of downstream circuit equipment is a premium concern. Fuses are also helpful for diagnostic purposes, aiding equipment designers and users in tracing the origin of the overcurrent faults.


Overcurrent Circuit Protection

The circuit designer has a choice of technologies when faced with the task of providing overcurrent protection. The traditional fuse and the Polymer based PTC (positive temperature coefficient) device represent the most common solutions employed. Understanding the differences between these two components simplifies choosing the best protection device for the application.

Fuses have been referred to as “one time” devices, in that the fuse will provide protection from the overload by opening only once and then it needs to be replaced. The heart of a typical fuse is a length of wire which is heated to its melting point by the excessive current. The circuit current flow decreases to zero as the wire melts open.

The PTC also reacts to the excessive current but is known as a “resettable” device. The polymer based unit can provide overcurrent circuit protection a number of times when reset by removing the overload. The conductive polymer increases in resistance when heated by the overload and limits the circuit current.


PTC Protection Function

The principles of operation for a fuse have been documented over the years and are generally well understood. The actual process by which the PTC provides overcurrent circuit protection is less clear and merits further discussion. So far the PTC has been identified as being polymer based, current limiting, and resettable.

The PTCs under discussion are conductive polymer based products. The polymer material used contains particles of carbon black as the conductive media. The resistance is controlled by the amount of carbon black introduced in o the mixture. Heat produces some expansion of the polymer which causes the carbon black to shift resulting in less conductivity or an increase in resistance.

The PTC functions by current limiting a potentially damaging overcurrent to a safe level. Specifically the excessive current through the device causes internal heating (I2R) which raises the temperature of the PTC and results in an increase in its resistance. The resistance of the PTC is generally a small part of the total circuit impedance until the heating takes place. The increase in resistance for a polymer based PTC is nonlinear as shown in the graph below and this relatively large increase in resistance will reduce or limit the circuit current to a safe level. The transition from low to high resistance is referred to as the trip point.

The heat generated by this limited current through the higher resistance value will maintain the temperature of the PTC at a level that will cause the resistance to remain high. This thermal equilibrium condition will continue until power is removed from the circuit which allows the PTC to cool down and the resistance will decrease. The resettable feature of the PTC is based on the fact that the increase in resistance resulting from the increase in temperature is reversible. The PTC is reset or returned to the lower resistance state by removing the power from the circuit which allows the device to cool down. The unit is then ready to react to future overloads. The resistance will remain low if the cause of the overcurrent has been corrected, but if the overcurrent recurs the device will again switch to the high resistance state.
 

主站蜘蛛池模板: 水处理设备_纯净水设备_软化水设备_反渗透水处理设备「陕西甘肃青海宁夏新疆」认准海川环保 | 重庆消杀公司-重庆斗哥环保科技-灭鼠公司-重庆灭蟑螂-除四害-灭老鼠-灭虫-重庆灭白蚁公司 | 网站主页 - 河北天成药业股份有限公司| 注塑机螺杆_光学无卤耐磨耐腐蚀螺杆_合金材料_螺杆研磨抛光机_杰宇螺杆 | 深圳社区邦家政公司-保姆_月嫂_育儿嫂 _早教育婴师_家政钟点工_家政培训_家政加盟- 社区邦优质生活服务 专业、标准化、便捷、安心,一站式家庭服务平台,服务专业有保障 ! | 河北热风机,电热暖风机,燃油暖风机,工业暖风机厂家安装,批发-河北嘉鹏冷暖风机有限公司 | 青岛家政网【家政港】青岛家政保姆网络服务平台! | 饲料车_散装饲料车_畜禽运输车_散装饲料运输车_饲料车厂家_铝合金运猪车-程力专用汽车股份有限公司 | 家居网链网—家居产业互联网价值平台 | 回收求购煤矿机械矿山设备,二手液压支架,刮板输送机-华建智能再生资源公司 | 中科迈金节能技术(浙江)有限公司 | 蓝禹太阳能蓄电池 风能储能胶体铅酸电池-扬州东泰电源有限公司 | 蒸汽发生器厂家-电加热蒸汽发生器-免办证/免报批/免报检电锅炉-上海电热水锅炉-上海艾亚锅炉有限公司 | 艺考培训-中影人教育 【官网】-中国艺考教育的引航者 | 凿岩机|操车设备|爬车机|三环链|伞钻|伞型钻机|中心回转抓岩机|往复式给煤机|滚轮罐耳|吊桶|钩头-济宁卓力工矿设备有限公司 | 升降炉|推板炉|创卓炉业 | 轮转印刷机_商标印唛机_超声波切唛机_瑞安市明辉机械有限公司 | 涂料分散剂_水墨分散剂-厚洹化学水性色浆助剂厂家 | 天津印刷_天津印刷厂_天津印刷公司_天津包装盒厂家_天津包装盒印刷厂_七层共挤膜厂家_彩色印刷_画册印刷_礼品盒定做 _七层共挤膜_食品真空袋-欢迎访问嘉联包装官网! | 芜湖表面处理-涂装-精密加工-阳极氧化-芜湖研历光电科技有限公司 | 浙江中瓷阀门有限公司| 以物联网技术为核心专注于智能安防领域物联网服务的高新技术企业-北京欣智恒科技股份有限公司(官网) | 绍兴凯渥人力资源有限公司-劳务派遣,劳务分包,代办公司注册 | 混凝土布料机,隧道布料机,衬砌台车布料装置 - 河北聚力智能装备有限公司 | 邮政纸箱_淘宝纸箱_抗压纸箱,盐城纸箱,盐城纸箱厂家,盐城承重纸箱-盐城君雅纸箱 | 山东正奇塑料机械有限公司,山东塑料机械,水带机组,塑料管材机,山东吹膜机组厂家,山东农膜机厂家 山东长青石油液压机械有限公司-致力于石油机械设备的研发制造,提供定制服务 | 无源电子锁_五防锁_机柜锁_物联网锁_智能锁控管理-Vanma | 西安网站建设,西安网站设计制作,西安短视频拍摄_短视频运营就选动力无限网络推广公司 | 烟台金海药业有限公司 | 首页--南京俊全科技有限公司,环保监测无人机,大疆无人机,农用无人机,植保无人机,巡检无人机,无人机环境监测仪,消防,无人机,航拍测绘,固定翼无人机,无人机电力巡检,四旋翼无人机 | 专业制造泥浆泵阀箱、锻造零件、曲轴、台阶轴等各种机械部件 - 四川中宇重工科技有限公司 | 中科联航(江苏)-信息化监理|信息化咨询|信息系统项目管理|信息系统工程监理公司 | 潍坊网络推广,临沂360推广,东营360推广,枣庄360推广,潍坊网站建设,潍坊网络公司,潍坊360搜索,潍坊APP开发,潍坊360推广,潍坊360代理,潍坊点睛网络科技有限公司 | 模具配件加工厂|东莞模具配件加工|模具配件加工厂|精密塑胶模具配件|东莞市优迪精密模具制品有限公司 | 西安木包装箱出口托盘定做价格-抽真空实木包装箱免熏蒸木箱多层板木箱哪家好-模压托盘及白松原木-西安宇森木业 | 水暖毯厂家-水暖毯配件-河北鑫政扬家用电器有限公司 | 中房网_中国房地产业协会官方网站 | 沥青灌缝胶-路面贴缝带-灌缝胶厂家-山东晟辉工程材料有限公司 | 智能电磁流量计-超声波流量计-涡街流量计-液体涡轮流量计-大连计测机器有限公司 | 塑胶模具定制,提供注塑加工服务,塑料模具制造厂_博腾纳公司 | 中昕国际项目管理有限公司-官方网站 |